Replies to This Discussion

Permalink Reply by Nicholas Tkaczuk on March 13, 2012 at 2:31am

Try Barnard's Schwinn in Oak Park.  I've had them install bottle bosses to my 68 Super Sport frame and it looks factory clean.   Plus custom made ferrules to fit existing cable guides (needed this done because of the difference between modern and orignal cable housing) and I think the cable guide under the bottom bracket was a three dollar item.   They do not look it but the are a full restoration and custom service shop, besides selling bikes.  If thy cannot do the braze-ons they probobly know and trust someone who can.  Plus they're local.  And I think they charged me $50.00 for the two bottle bosses.  One other thing the store is full of vintage perfectly restored schwinns, alot from the 60,s.  If you grew up in chicago and schwinns this place is like a candy store.

          http://www.barnardsschwinn.com/

• ▶ Reply

Permalink Reply by Michael A on March 13, 2012 at 2:59am

Use just cable guides and run the gear cable housing al the way to the front and rear derailleurs, if needed you could also add a small inline cable adjuster.  Clamp on solutions were used for many years. Until they come zip ties will hold your cables in place so you can get out and ride that new bike.

The bike shop was not wrong, a clamp on cable stop was never designed to be part of a modern sti shifting system. Any movement from the cable stop would result shifting issues.

• ▶ Reply

Permalink Reply by mike w. on March 13, 2012 at 7:29am

A properly installed clamp-on cable stop will not move.

Michael A said:

Use just cable guides and run the gear cable housing al the way to the front and rear derailleurs, if needed you could also add a small inline cable adjuster.  Clamp on solutions were used for many years. Until they come zip ties will hold your cables in place so you can get out and ride that new bike.

The bike shop was not wrong, a clamp on cable stop was never designed to be part of a modern sti shifting system. Any movement from the cable stop would result shifting issues.

• ▶ Reply

Permalink Reply by Melanie K on March 13, 2012 at 7:56am

I would like to thank everyone for all the great advice!  We have a clamp-on cable guide coming in the mail hopefully tomorrow, but since I was hoping to get this done by the weekend, does anyone know where I can get those mickey cable adjusters locally? Would a regular bike shop have them in stock? Would anyone have some they would be willing to part with?  We are using the "brifter" type shifters and right now have cable zip ties and duct tape holding the shifter cable housing to the down tube. I can shift 3 gears total on the back, but the line starts to slack, so I think I will need those barrel adjusters and the clamp to at least be able to shift decently. Right now, the bike is rideable, albeit as a 3 speed  LOL.  Thank you all again!

• ▶ Reply

Permalink Reply by S on March 13, 2012 at 9:10am

Your local bike shop should have these, however which derailleurs/brakes do you have?  There may already be adjusters on them.  

Melanie K said:

I would like to thank everyone for all the great advice!  We have a clamp-on cable guide coming in the mail hopefully tomorrow, but since I was hoping to get this done by the weekend, does anyone know where I can get those mickey cable adjusters locally? Would a regular bike shop have them in stock? Would anyone have some they would be willing to part with?  We are using the "brifter" type shifters and right now have cable zip ties and duct tape holding the shifter cable housing to the down tube. I can shift 3 gears total on the back, but the line starts to slack, so I think I will need those barrel adjusters and the clamp to at least be able to shift decently. Right now, the bike is rideable, albeit as a 3 speed  LOL.  Thank you all again!

• ▶ Reply

Permalink Reply by Melanie K on March 13, 2012 at 9:26am

It's just a Shimano Sora rear derailleur, and we have tried to use the barrel adjuster that is on the actual derailleur to no avail- it tenses it a bit, but there is still too much slack in the line that is on the downtube.

I'm going to check out a shop hopefully tonight to see if they have some in stock- I doubt they are more than $10, so even if I don't need them, just in case I do, I will have them. 

S said:

Your local bike shop should have these, however which derailleurs/brakes do you have?  There may already be adjusters on them.  

Melanie K said:

I would like to thank everyone for all the great advice!  We have a clamp-on cable guide coming in the mail hopefully tomorrow, but since I was hoping to get this done by the weekend, does anyone know where I can get those mickey cable adjusters locally? Would a regular bike shop have them in stock? Would anyone have some they would be willing to part with?  We are using the "brifter" type shifters and right now have cable zip ties and duct tape holding the shifter cable housing to the down tube. I can shift 3 gears total on the back, but the line starts to slack, so I think I will need those barrel adjusters and the clamp to at least be able to shift decently. Right now, the bike is rideable, albeit as a 3 speed  LOL.  Thank you all again!

• ▶ Reply

• ‹ Previous
• 1
• 2
• Next ›
• Page