I just finished this project and wanted to share the photos


I started with this my '09 Colnago EPS
Image

Then I took off the SR-11 parts, added a few new ones and made thisImage

Then I sent the Colnago EPS frame to Ruckus Composites to be converted for electronic shifting and a respray, first they stripped the paint Image

Then they drilled the new holes as needed, and filled the holes that were no longer neededImage

while they are working I gathered up these, Campagnolo SuperRecord 11 EPS V2 parts,

Image


They only used the head badge decal, everything else is masked and paint layers, the black is actually through to the bare carbonImageImageImageImage
Here is the finished project
Campy SR11 EPS except for the brakes
TRP mag's
Bora1 35mm
FMB service corsa tubulars
FSA plasma bar/stem
Selle Italia monolink seat post and saddle
Keo Blade 
tilquist garmin mount

7030 total weight as it sits
Image
Image
Image

Views: 1628

▶ Reply to This

Replies to This Discussion

Permalink Reply by Doug Haynes on January 7, 2015 at 3:31pm

Looks great!

Permalink Reply by Sol on January 7, 2015 at 7:08pm
LMAO! Really, who has a green milk crate?
Permalink Reply by Michael A on January 7, 2015 at 7:14pm
The milk crate is not to scale. I thought this is what you did for a living?
Permalink Reply by Jared on January 7, 2015 at 8:32pm

It's one of those fake ones they sell at Target.

Permalink Reply by David P. on January 8, 2015 at 4:38am

Is that a spacer I see under your stem?? I thought all you Italian-carbon weight-weenie types slammed your stems! :)

Permalink Reply by Michael A on January 8, 2015 at 5:02am
Because putting SRAM on a Colnago is like puiing cheese wiz in your lasanga !!
Permalink Reply by Louie Louie on January 8, 2015 at 6:39am

Very Nice, I like the vintage vibe of the decals.  You are now ready for the tour… Enjoy your ride

Permalink Reply by Eduardo on January 8, 2015 at 10:39am

You went for the colnago master paint job on an eps. Is the frame dark blue/purple or black?

Permalink Reply by Far'arned Retrogrumpalunkus #63 on January 8, 2015 at 10:55am

I looks pretty slammed to me.  I wouldn't be able to look further than 10 feet in front of the wheel with full neck extension upwards. 

Then again I have a short torso & arms with long legs and a bad back... 

Permalink Reply by Michael A on January 8, 2015 at 11:00am


When the EPS was released in 09 they did a very small run of these two colors, Zabel blue and Sarronni red. I wanted the blue but it was not available anymore, so I picked the red and white paint scheme. The blue is called Maseratti blue, it is a very deep blue with a slight metal flake background. They use this color in some of their newer bikes.


Eduardo said:

You went for the colnago master paint job on an eps. Is the frame dark blue/purple or black?

Permalink Reply by Michael A on January 8, 2015 at 11:04am

The headset top cap is about 8mm tall and curved, on top of that I have a .05 spacer and then another .05 spacer on top of the stem as per Colnago's recommendations for a carbon steerer tube. I could replace the top cap of the headset to get a little lower, or use a different angled stem but these measurements are for the fit set up I have had done.

David P. said:

Is that a spacer I see under your stem?? I thought all you Italian-carbon weight-weenie types slammed your stems! :)

Permalink Reply by Craig S. on January 8, 2015 at 12:43pm

You have an issue with bacon/cheddar Easy Cheez in lasagna?

Shit, my mistake, you said Cheez Wiz. 

Don't go blaspheming on my Easy Cheez!!!!

Michael A said:

Because putting SRAM on a Colnago is like puiing cheese wiz in your lasanga !!

RSS

Groups

© 2008-2016   The Chainlink Community, L.L.C.   Powered by

Disclaimer  |  Report an Issue  |  Terms of Service