Ohhhhhhhh yeah!

http://www.cobratiretool.com/

 

https://www.youtube.com/watch?v=u8P8K1WCY2w&feature=player_embe...

 

I would suggest.. Putting your derailleur, side up, not down.

Views: 254

▶ Reply to This

Replies to This Discussion

Permalink Reply by Kevin Mulcky on June 8, 2011 at 2:33am


Here's how you do it!
Permalink Reply by Melanie K on June 8, 2011 at 2:54am
Has anyone on here actually used this tool?  I would love for an easier way to change out a flat.
Permalink Reply by Kevin Mulcky on June 8, 2011 at 3:02am

Yea, that's a key step when you don't pinch flat. Otherwise you'll be doing another sub-two minute tire change a few miles down the road. I think the coolest part of this video is the wheel removal and remounting, it's just so smooth.

 

 

Chris C said:

They must have edited-out the part where he checks the tire to ensure the sharp object isn't still embedded in the tire.  About half of my flats require a tire glassectomy.
Permalink Reply by Joe Willis on June 8, 2011 at 4:14am
I would love to see ether one of these try thy changing a 700x23 gatorskin on a deep v wheel! I have to carry a small thing of dish soap just to change a flat!
Permalink Reply by S on June 8, 2011 at 4:59am
I haven't but with a tire lever, it's not too tough to pop the tire out.  Crank brothers have a speed lever that functions similarly and my experiences with that have been so-so.  I ended up sticking with regular tire levers.

Melanie said:
Has anyone on here actually used this tool?  I would love for an easier way to change out a flat.
Permalink Reply by S on June 8, 2011 at 5:01am
They also skip the part where a good part of the time using the tool to lever the tire back in results in the lever making a hole in the tube.  I've learned the hard way that you really want to use just your hands and thumbs to get the tire back in unless it's absolutely impossible with bare hands. 

Chris C said:
They must have edited-out the part where he checks the tire to ensure the sharp object isn't still embedded in the tire.  About half of my flats require a tire glassectomy.
Permalink Reply by Melanie K on June 8, 2011 at 5:10am
Darn, that is what I thought. I've punctured too many tubes using a lever to put the tire back on and now use only my thumbs and hands.  I was hoping this would be an alternative as I have some really tight fitting and hard to seat tires on one of my bikes. Is there any type of tool out there that can help re-seat a tire without using bare hands and/or brute force? 

S said:
They also skip the part where a good part of the time using the tool to lever the tire back in results in the lever making a hole in the tube.  I've learned the hard way that you really want to use just your hands and thumbs to get the tire back in unless it's absolutely impossible with bare hands. 

Chris C said:
They must have edited-out the part where he checks the tire to ensure the sharp object isn't still embedded in the tire.  About half of my flats require a tire glassectomy.
Permalink Reply by Kevin Mulcky on June 8, 2011 at 5:25am
Use bigger tires and you probably won't need tires levers at all.
Permalink Reply by Melanie K on June 8, 2011 at 5:39am
700 x 32 are not very small tires, but they are hard case/kevlar type tires and fit super tight on my rims. I don't get flats that often with them, but when I do, I either have to fight for 1/2 an hour to get the tire on the rim and seated correctly or look for a bike shop nearby. I can do it without the tire levers, but it is a pain. 

Kelvin Mulcky said:
Use bigger tires and you probably won't need tires levers at all.
Permalink Reply by Kevin Mulcky on June 8, 2011 at 6:06am

Dang, that's too bad. They will probably stretch out eventually. But certain tire/rim combinations can make for a really tight match. I mostly use 32mm Pasellas on the roads and a few different CX tires for off road. They all can be removed and mounted easily without levers.

 

I don't like hard case tires because their stiffness makes the ride more harsh, slower, and evidently harder to remove.

Permalink Reply by Far'arned Retrogrumpalunkus #63 on June 8, 2011 at 6:06am

+1000

 

The public streets are not a velodrome.  Save the skinny racing tires for the track...

 

Most tires I can use my fingers with.  Tough ones sometimes needs a pair of Pedro's tools (in hot pink as I dig Pinks and Purples.)  Then there are the really tough cases when even a pedro's doesn't cut it and then I use a Kool-Stop Tire Jack.  That thing can stretch out any bead and get it up and over the rim without damage to tire, tube, or rim -even the worst cases of malfitment.    

 

Some of the Sun-Riggle CR18 sizes run quite a bit tight for their stated ISO size, and if you are trying to get away with an old-style rubber rim strip and not using rim-tape they can be quite the bear to mount a tire on.  Once I even used Astroglide to help lube the tire when I was really stuck before I got the Kool-Stop jack. 

Kelvin Mulcky said:

Use bigger tires and you probably won't need tires levers at all.
Permalink Reply by ad on June 8, 2011 at 6:41am

A pair of wire bead Vittoria Randonneur 700 x 32 tires onto velocity deep v rims are some of the worse tires I have ever mounted, and that's including my experience mounting wire bead 700 x 28 and 700 x 25 Conti Gatorskins I run on my other two bikes.  Some tire and rim combinations are just destined to be a horrible experience.   

 

I second the recommendation on the Kool Stop Tire Jack tool.  Fairly cheap, and definitely the best tool I've found for mounting stubborn tires without damaging the tube.   

Melanie said:

Darn, that is what I thought. I've punctured too many tubes using a lever to put the tire back on and now use only my thumbs and hands.  I was hoping this would be an alternative as I have some really tight fitting and hard to seat tires on one of my bikes. Is there any type of tool out there that can help re-seat a tire without using bare hands and/or brute force? 

S said:
They also skip the part where a good part of the time using the tool to lever the tire back in results in the lever making a hole in the tube.  I've learned the hard way that you really want to use just your hands and thumbs to get the tire back in unless it's absolutely impossible with bare hands. 

Chris C said:
They must have edited-out the part where he checks the tire to ensure the sharp object isn't still embedded in the tire.  About half of my flats require a tire glassectomy.

RSS

Groups

© 2008-2016   The Chainlink Community, L.L.C.   Powered by

Disclaimer  |  Report an Issue  |  Terms of Service