MOM I Broke it.....(need advice)

Need advice as is obvious it was a one piece Deda but after looking on multiple web sites including Bianchi, Deda and Performance I get the impression that single piece stems have gone the way of the dodo am I wrong or should I just replace with a two piece? And I'm fine, thank you all, I know as I would have most would ask that question first I was stopped at a red light after putting in 50 miles for the day just lagging it home relaxing and when I started off from the light it snapped.

Views: 284

▶ Reply to This

Replies to This Discussion

Permalink Reply by Lucas Seibel on July 28, 2011 at 3:39am
Permalink Reply by Jack on July 28, 2011 at 3:41am

You could go either route.  Single piece stems are still available new.  I recently changed over my single piece stem on my Cannondale R-800 to a two piece.  When I looked, there are plenty of single piece stems out there.  Probably cheaper to go the single piece route, but I really haven't priced it out in a bit.

 

Glad to hear your "mishap" took place off from a start and not somewhere in the 50 mile ride.  Have a great day!

Permalink Reply by Mike Haring on July 28, 2011 at 3:43am

I think by "two-piece" you mean threadless stems, which are clamped directly to the fork, instead of inserted into the fork and held using an expander bolt. In order to use a threadless stem with your bike, you will need a threadless adapter, which are pretty easy to find and pretty cheap, but look kinda ugly, at least to some. Either that or a new fork, but 1" threadless forks are getting harder to find and there's probably no need for it. I would just go for a new threaded stem, personally, like the one that broke. It looks like the welds failed, though I have never seen that happen like that. You can get a Nitto stem for around $60 or less if you look: http://www.jensonusa.com/store/product/ST308B01-Nitto+Dynamic+Stem....

 

The disadvantages being that they don't have the bolt-on handlebar clamp, so you will need to unwrap/disconnect one side of your bars to install it. Also, they only come in silver, but they are very strong. There's also the Profile model still made, which has the bolt-on clamp, comes in black and is available to match the angle and length of your previous stem. Also cheaper than the Nitto:

http://www.universalcycles.com/shopping/product_details.php?id=7470...

 

Hope this helps.

Permalink Reply by Far'arned Retrogrumpalunkus #63 on July 28, 2011 at 4:21am

Ooof!

 

I am glad you didn't get hurt.  That looks like it could have been really nasty had it happened at the wrong place and time -and most places are the wrong place for a stem to break.  Having it happen even when one is alone on the road can still turn into a mouthful of teeth missing!  

 

Your LBS should be able to source a replacement part for you.  I would guess (don't quote me here) that this is a standard 1" stem with a quill size of 25.4mm and a bar size of 23.8 mm.  Amazon has a ton of them.  Find one with the same rise and reach as what you have now.  A "pop-top" type stem will be easier to install as you wont have to remove the brake and tape on one side to slide it in.

 

Or you can get a quill stem adapter and go with a threadless-type stem if that is what you want.  Either way is OK but I think that the adapter + threadless stem route will probably cost you more money in the end as you will be buying two things.  Amazon has some decent alloy stems for around $20.  

 

 

Permalink Reply by mindfrieze on July 28, 2011 at 4:47am
I highly recommend a Nitto Pearl stem.  They are beautiful and strong.  They are also available in black if that's your thing.  I usually end up buying them from Ben's Cycle in Milwaukee.  Take a look at all their available quill stems.
Permalink Reply by Kevin Mulcky on July 28, 2011 at 8:06am
If you can snap an aluminum stem in half - be sure your new stem is forged steel.
Permalink Reply by Far'arned Retrogrumpalunkus #63 on July 28, 2011 at 8:07am
Steel is REAL!
Permalink Reply by David Cummings on July 28, 2011 at 8:58am
Thank You all yeah I got REALLY lucky I'd done 50 miles at race pace and had just slowed down 2 blocks before to just lag home stopped at a red light and as I started to go POP....It was a Deda 310 Aluminum so my next will deff. be steel!
Permalink Reply by Kevin Mulcky on July 28, 2011 at 9:01am
Try a Nitto Jaguar if you're racing with it.
Permalink Reply by mark stetson on July 28, 2011 at 10:01am

Really lucky.  It was probably cracked for some time.  A good reminder for folks to look things over occaisonally, especially near tube junctions and welds.

 

Lots of people don't like the looks of a quill adapter with a threadless stem, but it does give you a lot more fit flexibility than sticking with a 1 piece quill stem.   If you don't need the adjustment that they offer, there's no reason not to replace it with another quill stem like you had.  Steel is an option, but I wouldn't think it's necessary.  Salsa and Nitto both made/make good steel ones. 

 

I would send the broken stem back to Deda, and see what they say.  If there was a problem, they will appreciate knowing about it.  They may even offer some compensation.

 

RSS

Groups

© 2008-2016   The Chainlink Community, L.L.C.   Powered by

Disclaimer  |  Report an Issue  |  Terms of Service